Vehicle Classifieds

Nashville, TN 22R Motor Runs on Propane All Toyota Running Gear Doubler Transfer Cases 4.10 Gears Double Rate Bilstein Coil Over Shock Front w/ 2.0 Shocks in Rear Shock Straps Rock Bar (Sway Bar) Propane Carb Extra Tanks Lincoln Locked Rear End Lock Rite Locker in Front Front Winch w/ Synthetic Rope Rear Winch TIRES: 39.5x13.50R15 Super Swamper IROC w/ 80% Tread Remaining New Tire on Spare Wheel Bead Lock Wheels 4 Linked Front and Rear Extra Rear End Housing Comes w/ It Very Light Buggy that Rides Very Soft Climbs and Crawls Extremely Well $9,500 OBO Mainly Looking for Cash but will Consider Reasonable Trades
Fully built jeep 2010 jk w/ 60k miles mostly highway auto trans , clean carfax title in hand , has over 30k in upgrades smittybilt xrc front stinger bumper , smittybilt xrc8k winch , smittybilt xrc front armor fenders , smittybilt xrc armor rear corners, smittybilt x c rock sliders , smittybilt xrc rear bumper & tire carrier, drake hood latches, k&n intake , Volant throttle body spacer, Msd speed demon ignition coil, livewire plug wires, e3 spark plugs, heavy duty starter , 180amp alternator, custom tig welded shock towers , engine cage , battery tray , abs module mount, mishimoto aluminum radiator, mishimoto aluminum trans cooler, 15" pro-comp beadlocks w/ orange rings, 1 1/2" hub centric wheel spacers, extended stainless steel braided...
Looking to sell or trade my 1972 Chevy Blazer for a capable street legal California Smog approved JEEP Power train: 1988 Corvette engine that now run using a carburetor (was a Tune Port Injection system). I still have all of the TPI parts that come with the sale, bought it this way and never installed it. 700r4 auto with shift kit, NP241 transfer case, GM 10 bolt front and rear. Rear has possi traction. I hardly drive the vehicle and it has been garaged during the time I’ve owned it. I occasionally take it for drives and haven’t done much off-roading. Replaced or repaired since purchase (2009): Intake seal, oil pres sensor, drivers side tie rod , rebuilt carb, motor mounts, master cylinder, radiator, thermostat and housing, plugs...
2002 Jeep Wrangler with the 4.0 motor. This jeep has low miles with only 61,500 it runs and drives great. Very hot heat and ice cold a/c. It has 35" nitto mud grapplers with bead lock wheels about 90% tread, high pinion dana 30 with chromolly axles, 8.8 with disc brakes, arb lockers front and rear, 4:56 gear ratio, 5.5" long arm, smitty built 8000# winch. Asking $13,500 obo clean title in hand. Call or text with questions and I can send more photos. 574-518-2311
Rock Crawler 4 Seater JEEP SAFARI!!! This is a great rig and will go over anything that you put in front of it and is very reliable. I hate to sell it and know I will later regret it, but I have a young family now and my interests and hobbies have changed. Build List: · Chopped and tubed from the dash back · Custom cage with 1 ¾” tubing · 4.0 L. engine with upgrades · Fuel cell · Atlas II 5.0 · Auto transmission · 40” Creepy Crawler Stickies with lots of tread on Trail Ready Bead locks · 120” wheelbase · High pinion Ford Dana 60 front with a new Detroit locker and ring and pinion used only once. · Ford Dana 70 rear with Lincoln locker · Hydraulic assist · Warn 9000 winch with new cable · New front drive...
1987 Jeep Wrangler!!!! The motor has been swapped to a 5.2 V8 out of a 2002 Jeep Cherokee with a little over 50,000 miles. Auto tranny swap. Dana 44 front and rear. Custom suspension. Poison spider rocker knockers and rear comp cutout rock guards. Spare tire carrier. Warn M8000 winch. ARB diff guard, rock lights, trans cooler, 15" beadlockers, warn hubs, Best Top soft top, ARB onboard air compressor with front and rear ARB diff locks, 36" TSL super swampers with full-size spare, oversized aluminum radiator. Will throw in 3" wheel spacers. CB radio. Call (801)941-5587 with questions. $7,000 OBO.
RUBICON TESTED! 93 Jeep XJ Custom built off road/rock crawler. Built specifically for the Rubicon Trail in CA. Long arm suspension, 33 inch Coopers on alloys, Billstein shocks, lockers, alloy axles, rear disk brakes, custom high steering, sub framed, sliders and well armored. Custom 8 point roll cage, winch mounted bumpers rear swing out spare carrier, on board air system for lockers and widened fender wells with one inch tube reinforcements and vented hood. AX-15 5 speed with heavy duty clutch and hand throttle mounted to gear shift. NP-231 transfer case with heavy duty chain and SYE. Dana 30 front alloy axles braced C's sleaved tubes. Rear Chrysler 8.25 shaved 29 spline alloy axles disc brake conversion. I built this jeep...
Only selling so I can buy a friends buggy...$8500 or $7500 without tires and wheels Built by Clayton Off road and unlimited Motorsports... 91 Jeep Cherokee Engine 4.0 ax15 with new heavier flywheel and Kevlar clutch np231 case hd slip yoke eliminator Axles Front Dana 60 high pinion 538 gears arb airlocker 35 spline inner and 35 spline outer chromoly shafts with rock crusher drive flanges and rock crusher diff cover new brakes complete high steer all new bearings Rear Dana 60 538 gears full spool rock crusher diff cover Tires and Wheels 40x13.5x18 Baja Claw Stickys (5) 18" Trailready Double Beadlocks Suspension Clayton long arm front all Clayton brackets on front 60 Custom Clayton 4 link kit long arm front and rear Clayton...
NOT a Jeep, but looks like a CJ7. Very capable car, has run with the best. Tube frame car custom built by ROCKWORX in 2008. LS1, 4L60, Altas 3.0, Rockjock 60's with Detroit Lockers front and rear, Aqualu aluminum tub slightly boattailed, NEW 39" BFG red labels on 17" Walker Evans bead lock wheels, Fox coilover shocks in front and Fox shocks on rear with coil spring suspension, winch, on-board compressor for tires, heater, aluminum tool box, Mastercraft seats with 5 point harnesses. Cost $70,000 to build today Asking $42,500
Rockwell 2.5 ton axles with Detroit lockers.. Pinion breaks ... Full hydro steering. 4 linked front and rear. Race runner nitrogen shocks... Brand new 355 Chevy crate motor. With fuel injection... Brand new th350 with stage 3 torque converter... Dana 300 with 1 ton out put shaft kits.. 4 to 1 low kit. Cromolly drive shaft in rear. Twin sticked. Line lock... Front and rear winches with 3 rd suspension winch up front.. Brand new 44 inch super swampers with brand new rockwell bead locks... Fuel cell.. ratchet shifter list goes on and on... Just in tires wheels and new powertrain I have what I'm asking ... $16,000 My loss is your gain . found a new toy and need this one gone 435-232-9071 chris
Bought as a pre-run rig for our 4400 Ultra4 Team. Its not needed by the team now so we are selling to facilitate more Racing Projects. Super stable and a blast to drive! Tons more done to this buggy! Runs perfect! Everything is how it should be! Can hang with the big dogs! Not used since rebuild! Seriously TURN KEY! Gladly take you for a ride! Super Fast and can crawl!! Price $44,000 Specs: 111" Wheelbase 86" Width 3,750 lbs 2008 Tube Chassis built by 4x4 Nation Sunray Engineering 1610 Rear Steer Axle 5.43 Gears Strange Nodular Drop Out Spool Wilwood Calipers Toyota FJ Hood/Cowl/Grille from Twisted Customs 4 Link Rear 3 Link Front 2010 NEW LS2 6.0 440HP all Aluminum Monster TH350 Cutom Torque Converter...
I have a FJ 40, 78 Land Cruiser. Leak over shocks, 37 inch tires, ARB locked. Special customized Roll cage, welded to frame. Small block V-8. Rhino guarded inside and out, special 4 point restraint seat belts, new seats. I was involved in a car accident, and no longer drive aggressive or rock crawling. I have not driven in two years, after market, modifications approx. $30,000. Asking $5000.00 as is. Docasgard@gmail.com
Kingpin 60s with chromolly shafts and CTM UJOINTS front and rear... Rear steer with custom high steer dule rams front and rear. Brand new 47 inch LTBs with new hummer dule bead locks that have been re centered . ORI shocks in front with 18" of travel 2.5 race runners in rear with 18" of travel. Fox bump stops . tom woods drive lines .. Atlas 2 transfercase. 4.6 all aluminum V8. With fuel injection... Rear mounted radiator that cools through the frame and back. Twin break peddles and master cylinders. Winch light bars .. Too much too list. Clean Utah title $21000 obo 435 232 9071
Hey Rockcrawler.com community, just wanted to post this here for a bit more exposure to some folks that may be interested in my CJ-7 crawler that I am selling. I will part it out, but only after I sell the axles which are a big part of the price. All the details below, glad to answer any questions. Some preliminary pricing can be found on the jeepforum posting here. Asking $13,500 Thanks for looking! More Pics: 83 CJ-7 Selling my well built CJ-7. This is not set up as a daily driver, this is a pure off-road rig. The Atlas II, driveshafts, and Prorock 60's have less than 150 miles on them. The 4.0 HO and the AW-4 came from a '91 XJ with 83k on it. Most work has been professionally done / fabbed on this jeep by High Country...
4 door lifted, fully loaded from Jeep, 5 speed, no accidents, some scratches (as usual), Original owner and I have done the modifications through a qualified garage and by myself, tow package and trailer brakes, soft top and hard tops included, 145,000 km only. Asking $30,000 CDN. Total of additional parts added to the vehicle is $27,798.61 I have been to Moab several times, and you can view my Jeep on trails with the crew from Rebel Off Road Easter Jeep safari 2014.They have helped me build and service my Jeep. Also I have made a video on You Tube of my Jeep for viewing: https://www.youtube.com/channel/UCh_ZS3VUw1L_2mojEGTup5g Special features as follows to those who know about off road products: * King Shock conversion...
Drivetrain: 02 GM 5.3 with Jim's Performance harness and tune. Has truck intake, oil pan, and accessory drive. Custom headers and 2.5" exhaust with a single Magnaflow muffler. TH 400 transmission with stock converter.... reverse valve body so it will hold first gear at any rpm. Clocked and Twin Sticked 205. 1350 yokes. Axles: -Front is a Chevy LP 60 with Dodge external style hubs. 5:13 Gears and welded carrier. Have 35 spline Chrome Moly inners and outers. 2x3 3/16" wall box tubing truss. 6" stroke DE ram with 3/4 heims on tie rods. BTF diff cover and 1350 yoke. -Rear is a 14 Bolt with BTF diff cover and brake brackets with 3/4 ton rotors and calipers. 5:13 Gears and Detroit Locker. Also has a 2x3 3/16" truss 1350 yoke. Chassis...
Where to start... 2001 White Tacoma 2.7 contributed to by Central Coast 4WDrive in Santa Cruz California (gears, bearings, etc.), JJ's Fabrication in Davenport California (axles, brakes, tubing) and Earnie's Service Center in Felton, California (engine overhaul). 4160 pounds and 25k minimum of project nearing completion. 3/4 ton true track front and rear. Custom bed with specialty front and real extra-wide panels. 488 gears, rebuilt engine and 3rz supercharger, K&N performance Kit, both rebuilt at 89,812k. Current odometer 94,300, shipped from CA to New Mexico on flatbed. New Ball joints, new link bars, springs. Parking brake line lock. Ballistic front shocks, warn 9.5 cgi winch fits front and back with remote, optima battery. Pioneer...

Members online

Back
Top Bottom