1981 cj7 professionally built rockcrawler daily driver.
2007 5.3 vortex
Mild cam
Headers
Tci 700r4 trans
1 tons front and back
Four link all the way around
Rhino line inside and out
Rollcage to frame
Much more
Drivetrain:
02 GM 5.3 with Jim's Performance harness and tune.
Has truck intake, oil pan, and accessory drive.
Custom headers and 2.5" exhaust with a single Magnaflow muffler.
TH 400 transmission with stock converter....
reverse valve body so it will hold first gear at any rpm.
Clocked and Twin Sticked 205.
1350 yokes.
Axles:
-Front is a Chevy LP 60 with Dodge external style hubs.
5:13 Gears and welded carrier. Have
35 spline Chrome Moly inners and outers.
2x3 3/16" wall box tubing truss.
6" stroke DE ram with 3/4 heims on tie rods.
BTF diff cover and 1350 yoke.
-Rear is a 14 Bolt with BTF diff cover and brake brackets with 3/4 ton rotors and calipers.
5:13 Gears and Detroit Locker.
Also has a 2x3 3/16" truss
1350 yoke.
Chassis...
2005 Jeep Rubicon unlimited w/79k miles, 4.0, 6spd manual transmission. Clean title. Asking $18,000.00 obo. Here is the list of mods:
4 linked Dana 44 front axle (from 79 F250) 4.10 gears
3 linked Dana 60 rear axle (from 79 F250) 4.10 gears
Stainless steel braided brake lines
Long air suspension kit (6.5 lift overall)
High steer arms (components all made with DOM 1/4" wall tubing)
38" XML's
Custom bumpers front and rear
Custom front fenders
12,000lbs hydraulics wench (driven off the power steering pump)
Remote for wench plugs into the dash inside the jeep
Sport cage - corbeau seats
Touch screen head unit w/navigation, CD, and DVD
9 speaker stereo (amped)
4.0 6cylinder fuel injected
6 speed manual transmission
Borla stainless steel...
Hey Rockcrawler.com community, just wanted to post this here for a bit more exposure to some folks that may be interested in my CJ-7 crawler that I am selling.
I will part it out, but only after I sell the axles which are a big part of the price. All the details below, glad to answer any questions. Some preliminary pricing can be found on the jeepforum posting here.
Asking $13,500
Thanks for looking!
More Pics: 83 CJ-7
Selling my well built CJ-7. This is not set up as a daily driver, this is a pure off-road rig. The Atlas II, driveshafts, and Prorock 60's have less than 150 miles on them. The 4.0 HO and the AW-4 came from a '91 XJ with 83k on it.
Most work has been professionally done / fabbed on this jeep by High Country...
4 door lifted, fully loaded from Jeep, 5 speed, no accidents, some scratches (as usual), Original owner and I have done the modifications through a qualified garage and by myself, tow package and trailer brakes, soft top and hard tops included, 145,000 km only. Asking $30,000 CDN. Total of additional parts added to the vehicle is $27,798.61
I have been to Moab several times, and you can view my Jeep on trails with the crew from Rebel Off Road Easter Jeep safari 2014.They have helped me build and service my Jeep. Also I have made a video on You Tube of my Jeep for viewing: https://www.youtube.com/channel/UCh_ZS3VUw1L_2mojEGTup5g
Special features as follows to those who know about off road products:
* King Shock conversion...
383 Stroker Engine; 700R4 Transmission, ½ Ton Axles, Yukon Gears, 5.42 Ratio; Full Locker Front and Rear Custom Cage; 38” Super Swamper Tires; Warn Power Plant 9500 Pound Wench. Price: $8,500 OBO.
Kingpin 60s with chromolly shafts and CTM UJOINTS front and rear... Rear steer with custom high steer dule rams front and rear. Brand new 47 inch LTBs with new hummer dule bead locks that have been re centered . ORI shocks in front with 18" of travel 2.5 race runners in rear with 18" of travel. Fox bump stops . tom woods drive lines .. Atlas 2 transfercase. 4.6 all aluminum V8. With fuel injection... Rear mounted radiator that cools through the frame and back. Twin break peddles and master cylinders. Winch light bars .. Too much too list. Clean Utah title $21000 obo 435 232 9071
Bought as a pre-run rig for our 4400 Ultra4 Team. Its not needed by the team now so we are selling to facilitate more Racing Projects. Super stable and a blast to drive! Tons more done to this buggy! Runs perfect! Everything is how it should be! Can hang with the big dogs! Not used since rebuild! Seriously TURN KEY! Gladly take you for a ride! Super Fast and can crawl!!
Price $44,000
Specs:
111" Wheelbase
86" Width
3,750 lbs
2008
Tube Chassis built by 4x4 Nation
Sunray Engineering 1610 Rear Steer Axle
5.43 Gears
Strange Nodular Drop Out
Spool
Wilwood Calipers
Toyota FJ Hood/Cowl/Grille from Twisted Customs
4 Link Rear
3 Link Front
2010
NEW LS2 6.0 440HP all Aluminum
Monster TH350
Cutom Torque Converter...
1987 Jeep Wrangler!!!! The motor has been swapped to a 5.2 V8 out of a 2002 Jeep Cherokee with a little over 50,000 miles. Auto tranny swap. Dana 44 front and rear. Custom suspension. Poison spider rocker knockers and rear comp cutout rock guards. Spare tire carrier. Warn M8000 winch. ARB diff guard, rock lights, trans cooler, 15" beadlockers, warn hubs, Best Top soft top, ARB onboard air compressor with front and rear ARB diff locks, 36" TSL super swampers with full-size spare, oversized aluminum radiator. Will throw in 3" wheel spacers. CB radio. Call (801)941-5587 with questions. $7,000 OBO.
Rock Crawler 4 Seater
JEEP SAFARI!!! This is a great rig and will go over anything that you put in front of it and is very reliable. I hate to sell it and know I will later regret it, but I have a young family now and my interests and hobbies have changed.
Build List:
· Chopped and tubed from the dash back
· Custom cage with 1 ¾” tubing
· 4.0 L. engine with upgrades
· Fuel cell
· Atlas II 5.0
· Auto transmission
· 40” Creepy Crawler Stickies with lots of tread on Trail Ready Bead locks
· 120” wheelbase
· High pinion Ford Dana 60 front with a new Detroit locker and ring and pinion used only once.
· Ford Dana 70 rear with Lincoln locker
· Hydraulic assist
· Warn 9000 winch with new cable
· New front drive...
Rockwell 2.5 ton axles with Detroit lockers.. Pinion breaks ... Full hydro steering. 4 linked front and rear. Race runner nitrogen shocks... Brand new 355 Chevy crate motor. With fuel injection... Brand new th350 with stage 3 torque converter... Dana 300 with 1 ton out put shaft kits.. 4 to 1 low kit. Cromolly drive shaft in rear. Twin sticked. Line lock... Front and rear winches with 3 rd suspension winch up front.. Brand new 44 inch super swampers with brand new rockwell bead locks... Fuel cell.. ratchet shifter list goes on and on... Just in tires wheels and new powertrain I have what I'm asking ... $16,000 My loss is your gain . found a new toy and need this one gone 435-232-9071 chris
355 tbi engine
350 turbo tranny
205/203 doubler transfer case twin stick
Dana 60 front end Yukon axles
14 bolt rear end Yukon axles
Full four link set up
10,000 lbs winch on front 4,000 lbs winch on rear
Fox shocks with 18 inches of travel
42 inch tires with bead locks
15 gallon fuel cell
9500$
Much more.. call or text (270)980-2448
NOT a Jeep, but looks like a CJ7.
Very capable car, has run with the best.
Tube frame car custom built by ROCKWORX in 2008.
LS1, 4L60, Altas 3.0, Rockjock 60's with Detroit Lockers front and rear,
Aqualu aluminum tub slightly boattailed, NEW 39" BFG red labels on
17" Walker Evans bead lock wheels, Fox coilover shocks in front and
Fox shocks on rear with coil spring suspension, winch, on-board compressor for tires,
heater, aluminum tool box, Mastercraft seats with 5 point harnesses.
Cost $70,000 to build today
Asking $42,500
Nashville, TN
22R Motor Runs on Propane
All Toyota Running Gear
Doubler Transfer Cases
4.10 Gears
Double Rate Bilstein Coil Over Shock Front w/ 2.0 Shocks in Rear
Shock Straps
Rock Bar (Sway Bar)
Propane Carb Extra Tanks
Lincoln Locked Rear End
Lock Rite Locker in Front
Front Winch w/ Synthetic Rope
Rear Winch
TIRES: 39.5x13.50R15 Super Swamper IROC w/ 80% Tread Remaining
New Tire on Spare Wheel
Bead Lock Wheels
4 Linked Front and Rear
Extra Rear End Housing Comes w/ It
Very Light Buggy that Rides Very Soft
Climbs and Crawls Extremely Well
$9,500 OBO
Mainly Looking for Cash but will Consider Reasonable Trades
RUBICON TESTED! 93 Jeep XJ Custom built off road/rock crawler. Built specifically for the Rubicon Trail in CA. Long arm suspension, 33 inch Coopers on alloys, Billstein shocks, lockers, alloy axles, rear disk brakes, custom high steering, sub framed, sliders and well armored. Custom 8 point roll cage, winch mounted bumpers rear swing out spare carrier, on board air system for lockers and widened fender wells with one inch tube reinforcements and vented hood. AX-15 5 speed with heavy duty clutch and hand throttle mounted to gear shift. NP-231 transfer case with heavy duty chain and SYE. Dana 30 front alloy axles braced C's sleaved tubes. Rear Chrysler 8.25 shaved 29 spline alloy axles disc brake conversion.
I built this jeep...
Nashville TN
88 Toyota Truggy
Rebuilt 22RE with no leaks, very strong
Stock Toyota 5 Speed
4.7 Gear Reduction
Front Axle: Chevy D60 456 Gears Lincoln Locked with Great Lakes HD Cover, CUCV Axle
Rear Axle: 14 Bolt with Detroit Locker 456 Gears with Disc Brakes, CUCV axle
4" Spring Lift, Blocks and Shackles for a total of 9" lift
Steering is Fully Hydraulic with Ag Cylinder
124" Wheel Base
The Bed is Steel Tread Plate
16 x 10 Black Steel Wheels
15 x 38.5 Bogger Tires with New Spare
12000 lb Vortex Winch
New Shocks and Brakes
Off Road Seats with 5 Point Harness
Rock Lights on the Front and Rear
CB radio, Tool Box, Fuel Cell
Im sure Im leaving some things out. Respond with any questions.
Price is firm
Email for more Pics
TonyK Unlimited single seat chassis
Mid-engine 2.2 Ecotec
A-904 tranny
5:1 Atlas
9" axles with Detroits and 6.50 gears
Line lock on the front brakes
Cutting brakes on the rear brakes
(5) 39" red label Krawlers on 17x8 Method beadlocks
Rear suck-down winch (Summit 3000lbs)
Front WARN 9.0Rc winch
Griffin radiator
Very capable. Fairly competitive in both CalROCS and WERock (passed tech for both)
I am currently going through everything, including re-building the transmission as it blew a seal at the input shaft at the WERock Nationals. It will be running and ready for the next comp season.
$16000 is my bottom line
2002 Jeep Wrangler with the 4.0 motor. This jeep has low miles with only 61,500 it runs and drives great. Very hot heat and ice cold a/c. It has 35" nitto mud grapplers with bead lock wheels about 90% tread, high pinion dana 30 with chromolly axles, 8.8 with disc brakes, arb lockers front and rear, 4:56 gear ratio, 5.5" long arm, smitty built 8000# winch. Asking $13,500 obo clean title in hand. Call or text with questions and I can send more photos. 574-518-2311
1985 Jeep CJ-7 for sale. Red in color rust free this jeep is from Louisiana so it has never been in the salt. This is a custom vehicle from top to bottom but is registered, inspected, licensed and insured in the state of Missouri. Its street legal and drives great this jeep is ready to wheel. Drivetrain; fuel injected 350 5.7L Chevy motor with the factory matched 4L80E transmission with art Carr shifter, ATLAS II transfer case with twin stick shifters, 1 ton rear driveshaft, ½ ton front driveshaft, the exhaust is two into one with flow master muffler. Both front and rear axles are custom built shaved spider 9” axles with 4:56 gears, air lockers and 35 spline Moser axles. Disc brakes front and rear. These axles are 5 lug 5on 5.5...
'97 Wrangler 4.0L, 5 Spd, A/C, 110,000 miles
Adds include:
Teraflex Long Arm Suspension with Bilstein Shocks and Sway Bar Disconnects
ARB on board air compressor with front and rear differential locks
5:13 gears with alloy USA axles
5 Goodyear Tires MT/R 35x12.50x15 with Kevlar on Helo wheels, spare has never been on the ground
Warren XD 9000I winch with remote
SOLID differential covers
Custom steel fenders, with aftermarket front and rear bumpers and swing away rear tire carrier
WET AKOLE Hawaii wet suit seat covers
Exhaust header
Undercarriage lighting
CB Radio
Hand throttle
New radiator and brakes
Please email for more pics. $18,000 OBO
Looking to sell or trade my 1972 Chevy Blazer for a capable street legal California Smog approved JEEP
Power train: 1988 Corvette engine that now run using a carburetor (was a Tune Port Injection system). I still have all of the TPI parts that come with the sale, bought it this way and never installed it. 700r4 auto with shift kit, NP241 transfer case, GM 10 bolt front and rear. Rear has possi traction.
I hardly drive the vehicle and it has been garaged during the time I’ve owned it. I occasionally take it for drives and haven’t done much off-roading.
Replaced or repaired since purchase (2009):
Intake seal, oil pres sensor, drivers side tie rod , rebuilt carb, motor mounts, master cylinder, radiator, thermostat and housing, plugs...
Custom Toyota rock crawler trail climber. 22r motor with 70k on rebuild. Custom racing seats bobbed and narrowed bed with rhino liner. Nothings leaks runs great and is street legal . The AC and heater both work. Tons of mods.clean title5:29 gears front and backozzy locker in the front and welded in the rear4:70 in the t-casedirty 30's4 inch lifttrail gear in front and chevy springs in the rear37 inch tiresfront axle pushed 2 inches forwardcustom rock slidershi-steering.4800 obo. dont need help selling it. 505 two five nine 88 eight zer
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.